Creative position statement:

The goods measured in this article are purchased at their own expense. If you get the activities of participating in Aunt Zhang, I will make it clear in the text. Adhering to the independent evaluation view is the basic bottom line created by the author, and will never bias because of different sources of goods. Please rest assured.

Last month, I found a low -cost and low -power quad -core AMD thin client in the seafood market, so it was worth buying and sharing the disassembly of this machine, because the original intention of buying this machine was to be a remote Baidu network disk remotely. Download, so I only install the WES7 system, but the friends are more concerned about whether they can change the dual -net meter Gigabit soft route. Today, it comes, it is still a three -net meter Gigabit!

If you want to know this machine configuration and disassembly map, you can click on my personal homepage or the super link above to read my previous article. It is no longer anecdotic, and the process of turning the explosion directly below.

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

Before the explosion reform, first look at the internal space of the machine, and then decide to buy accessories. At the beginning, I only looked at it roughly, but I didn’t take the ruler carefully, so I ate a small loss.

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

wyse5020 chassis internal space

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

As shown in the figure above, I just looked at it roughly, thinking that the red circle could put down the high minipcie, and the green circle can put two RJ45 network ports, so I went to Taobao to buy a full -high minipcie to the RTL8111 dual -mouth network card.

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

Inappropriate network card

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

As a result, the interface of the data cable found that the data cable was straight, and the installation was installed, but the 2.5 -inch hard disk could not be stuffed after that, and the distance between the two mesh ports was too far, causing the meson to top the heat pipe of the radiator. Fortunately, the seller was good at talking, agreed to return the goods, and lost a small loss.

I had to go to Taobao to find the right network card again. Many suitable data interfaces are bending needles with Intel chips. A set of more than 200-300 yuan, really unwilling. After all The difference between the dual -net port and the three net ports is not much different. Maybe the heavens can see it in order to make it cool. In the end, I found a cheap. Although the interface is a straight needle, the data line DuPont head is 90 ° double -port with a 90 ° port. Net card. Double 11 special offer 139 yuan, store coupon-5, use Taobao money card-6, superimposed cloud flash payment 10-3 payment discount, last 125 to hand, 100 yuan cost explosion, three network mouth soft routes!

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

SSU double -port 811H network port

It can be seen that this is to use ASM1182E (PCI Express’s group exchange IC chip differential clock cusher), and divide one PCIE to two crabs RTL8111h. In this way, the performance of the transition than the single -network port transfer card will be lost, and the value friends who understand can be guided in the comment area.

Then try to put the dvi interface on the mesh port. Try enough space.

DVI interface

The preliminary attempt can be perfectly stuffed. The width of the dual -net port is just the same as the direct width of the two fixed copper columns in the DVI interface.

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

Without saying a word, do it directly, remove the side plates on both sides, and then remove the two fixed copper columns of the DVI interface, and the baffle can be taken down. If you do n’t understand the dismantling, please read the disassembly article in front of me (the low -power AMD quad -core thin client (Dell WYSE5020) with the underestimated performance (Dell WYSE5020))

Dismantle the copper column

Metal aviation shear

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

Cut into small strips first, then cut the small strip

Gouring finished mesh

The amount is about the size, not too accurate, it doesn’t matter if the bigger and small, and then directly cut the violence of metal aviation, cut it into a small strip first, then cut it off. hand.

Brother AB glue

Take out my collection of brothers AB glue for many years.

AB glue coating DVI interface

Apply the brother to the DVI interface evenly, and the location of the mesh port with the baffle can also be applied more stable.

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

Net port transformation is completed

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

In this way, the most difficult mesh and baffle transformation is completed, and the next step is to fix the network card.

Semi -high copper column

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

The copper column taken down

The motherboard supports the high minipcie, but the copper column is in a half -high position, and this copper column is more normal. It is necessary to use the soldering iron into the screw hole to heat the entire copper column to remove it.

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

The network card installation is complete

Welding the taken copper columns to a high position, you can install the network card smoothly.

Perfection

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

Use the data cable to connect the network card and the network port, streamline the line, and the transformation is complete! Perfect

2.5 inch hard disk

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

After the transformation, you can still plug a 2.5 -inch hard disk!

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

Insulatory tape

When the lid is covered, remember to stick the insulating tape to the place where the network card and the middle cover are contacted to prevent short circuits.

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

The transformation is successful!

I do n’t understand the soft routing, and now I started to play. Refer to the old man ID of the big man in the site (the soft route system installed OpenWRT). I preliminarily installed it. I will share the installation process of the WYSE5020 here. For reference, please excavate the specific functional gameplay.

First prepare a U disk to install the PE system (you need to support the PE startup of UEFI, otherwise the mirror download later, please select Legacy), download OpenWRT-GDQ-V9-1 [2021] -X86-64-SQUASHFS-UEFI .img.gz) and the writing tool (physdiskwrite.exe) put it on the PE U disk. All the tools come from the old man in the station.

Advanced

Put on Delete into BIOS, default password Fireport, enter Advanced, check whether the Boot from USB is enabled, and the last Boot Mode changes UEFI. (If you download the leggal image, choose Legacy.) Press F10 to save and restart.

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

Boot menu

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

After restarting, press the keyboard “P” to enter the BOOT MENU, select your USB flash drive USB HDD, and press Enter to load the PE system.

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

Win+r

After entering the PE system, press the keyboard to win+r (or start -run), enter the CMD, and press Enter.

The first step enters the U disk

At CMD, the big guy ’s vetera

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

The first step (the original leakage said this step), enter the “U: U: enter the U disk in the Enter in the CMD dialog box, where U is your U disk formation, and generally defaults U. Revise. After CMD enters the U disk, it will become u:>

The second step is to drag the writing tool physdiskwrite.exe into the dialog box (no need to press Enter after dragging in), and then enter “space -u space” (original saying -u-, no additional add-after u), then the mirror image is then used The file OpenWRT-GDQ-V9-1 [2021] -X86-64-GENERIC-SQUASHFS-UEFI.img.gz is dragged into the dialog box, press Enter, then prompts you to choose the hard disk, find your hard disk or Drive1 or 2 or 2 , 3 et al. (The default is 0). After entering 0, press Enter, you will prompt you to format the hard disk. After entering Y, press Enter to write the image to the hard disk.

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

U:>

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

When U:> appeared again, it proves that the image has been successfully written to the hard disk and unplugged the U disk to restart the computer.

After the restart, it is prompted to press Enter to activate the console

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

After pressing the car, OPENWRT was successfully run. Use the network cable to find the LAN port to connect to the computer. The browser input 192.168.5.1 into the OpenWRT management interface (if no reaction indicates that you are not connected to LAN port, try another mouth)

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

OpenWrt Overview

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

OpenWrt initial gateway IP: 192.168.5.1 Initial user name: root password: Password, after entering the overview, all three network ports were recognized, and the network cables were operated at the rate of Gigabit all -duplex.

百元戴尔Wyse5020四核AMD瘦客户机爆改三网口OpenWrt软路由

Well, this is here this time, I just entered the pit soft route, and many gameplay will not be able to simply share the installation steps today. The main thing is to transform the three network ports. By the way Recognize. If you like to like the collection and reward, I will have more motivation to discover cheap and fun machines to share it with everyone.

This article is reproduced by the author of the community@本 本 本 本 本 本 本 本 本 本 本 本 本 本 本 only represents the author’s point of view. It has nothing to do with the position of this site. Do not reprint without authorization.

You might also enjoy: