When we decorate our home, we need to pave a lot of land. The most commonly used method for floor tiles is dry shops. So many friends will pay attention to the specific process of floor tiles. However, the paving of floor tiles not only contains the paving of the tiles on the ground, but also includes the early design, typesetting, and the treatment of the corner parts in the later period. Therefore, for the entire process and paving method of floor tiles, the home mixed altar summarizes the following three steps.

(1): The design of the ground paved

Before the floor tiles are paved, everyone must be designed. That is, the typesetting design of floor tiles. Like many designers now, they can type typography directly on the computer according to the size of the specifications we require. And if there is no computers in our family, we can also design it ourselves. Therefore, before the floor tile is paved, do the following work.

① Confirm the size of the floor tiles.

This is a very critical step. We need to design the ground, and we must first choose floor tiles suitable for specifications. For example, the current living room is generally paved with 800mm × 800mm, or 600mm × 1200mm, or 750mm × 1200mm to floor tiles. We can choose the right floor tiles from these specifications.

想把地砖铺好,铺贴方法很重要,3个步骤是其中的关键

② Camping of floor tiles.

想把地砖铺好,铺贴方法很重要,3个步骤是其中的关键

We can typeset after confirming the size of the floor tiles. When typing, we must first measure the length and width of the room, and the position of the specific door, and then we can use the size of the floor tiles we choose to typeset indoors. When typography, you must consider the gap between the floor tiles. Personally, everyone is that we are paving floor tiles in the living room, and generally leave a gap of 2mm. You can leave a little more with the parts of the wall, such as leaving 5mm gaps. You can type floor tiles in our room in turn.

(2): Test shops before the tile paving

想把地砖铺好,铺贴方法很重要,3个步骤是其中的关键

Our base tile design and size selection and typesetting can be paved with our floor tiles. Before the floor tile is paved, we must first choose the starting position of the paving when paving the bricks. Because the selection of the starting position also determines the specific size of the floor tiles paved later. Therefore, I recommend that you follow the following steps.

① Selection of the starting position.

For the choice of the starting position of indoor tiles, the location is different depending on the room. For example, the bathroom, it is recommended that you spread the first brick from the inner side of the bathroom, and then retreat to the outside. For living rooms or restaurants, it is recommended that you put it from the balcony to the entrance door. For the kitchen, spread it from the inside of the kitchen, so that we confirm the location of the first brick.

② Test the shop.

The so -called test shop is to make the floor tiles on the ground to confirm the specific size. For example, the floor tiles we paved the bathroom first, first put the first floor tile code on the ground, then dry the floor tiles on the ground, and finally to the door. This can accurately find the size of the half brick in our bathroom floor. Of course, if our early layout is very accurate, this step can be omitted. However, if there is no typesetting map, it is recommended that you find the position of the last half of the brick.

(3): The formal paving of tiles

The official paving of floor tiles refers to some methods that are actually paved. Like the commonly paved methods of home decoration are all dry shops. The so -called dry shop is to use dry mixing cement mortar on the ground, then apply cement slurry on the back of the tile, and finally put the floor tiles onto the cement mortar layer. This completes the paving of floor tiles. In this process, I recommend that you follow the following steps.

① Clean the ground.

Before paving the ground tiles, you must clean the ground, otherwise there may be empty drums. The first thing we need to do is to use a broom or a vacuum cleaner to clean the dust on the ground. Then you can sprinkle a layer of water on the ground to keep the ground moist, or sprinkle a layer of cement slurry on the ground to curing the ground. Everyone should pay attention to clean up a area and lay a area. Do not clean up the floor tiles in large areas, otherwise the ground will cause pollution after cleaning.

② The paving of cement mortar.

想把地砖铺好,铺贴方法很重要,3个步骤是其中的关键

In fact, the second step is to pave the cement mortar. Before paving cement mortar, we must stir cement mortar. The mixed cement mortar uses cement and sand, and adds a certain amount of water to stir into cement mortar. At this time, the mixed cement mortar is a dry mixed cement mortar. Dry mixing cement mortar is held together with hands, and then loosened, showing a loose state. Pour these dried cement mortar to the location where we need to pave the ground tiles. Personally, we recommend that you pave the width of two bricks, and then prepare ground tiles.

③ Paste the floor tiles.

Before the floor tiles are paved, be sure to clean the back of the floor tiles. After that, we can use cement slurry to apply the tiles to the back of the tile, or use a dedicated tile glue to apply a sawtooth scraper to the back of the tile. After that, we paved the ground tiles with cement slurry to the dry paved cement mortar layer. According to the height of the line we play in advance or the infrared level, we can use a rubber hammer to knock. In this way, you can put all the indoor floor tiles.

④ Conservation of floor tiles.

想把地砖铺好,铺贴方法很重要,3个步骤是其中的关键

After the floor tile is paved, another very important step is to maintain. Because the drums in many floor tiles in the later period are caused by improper maintenance. The advice given here is that after the floor tiles are paved, try not to step on people within a week. If conditions permit, in some seasons that are particularly dry, you can sprinkle some water on the floor tiles to keep the surface moist. After maintaining more than a week, the surface is paved with a protective film so that our floor tiles are all completed.

Conclusion

Regarding the paving of floor tiles, many friends may only pay attention to the specific process of floor tiles. In fact, the quality of the floor tiles pave the quality, including the design of our paving drawings and the review of the size in the early stage. In the later stickers, the whole process is very critical. Therefore, if we plan to pave the floor tiles in our house, I suggest that everyone must accurately measure the size of each of our rooms. Then typeset the floor tiles in the room that need to be paved according to the size of the room. Remember the gap between the floor tiles and the floor tiles during the typesetting process. In this way, you can follow this program, and basically you can put a very good floor tile. Finally, it is reminded that the paving of the tiles in our room, try to use the sewing stickers as much as possible. Because seamless paving is easy to step on the pit, and it is easy to have empty drums in the later period.

[Personal original, the picture comes from the Internet, the infringement contact is deleted]

You might also enjoy: